Elements Archive - Tibek CNC-Technik - Makers of SmartWOP

Double doors without linking

Ralf Raaf — Thu, 17 Aug 2023 11:03:39 +0000

Linked doors have grayed out the “Double Door” feature. How can I now create a double door if several volumes are to be covered by it?

With the right order. In SmartWOP, from outside in worked. The order in which each item is indented is very important.

Double doors without linking

As an example, we use a cabinet with a notch at the back right.

As you can see below we have a double door, although several volumes are spanned here. So how do you go about it?

Step 1:
volume and left side

To do this, pull in a base and the vertical plate as normal.

Step 2:
Open the door and tick the double door box

Then use the F key to hide the doors to make it easier to edit the inside.

Step 3:
Place horizontal and vertical dividers

Step 4:
Place frontal divider

Step 5:
right side

To do this, the volumes must be selected. To do this, press the V key and click on the first volume in front.

Hold down the STRG/CTRL key and then select the second volume.

Now the page can be drawn in on the right.

Step 6:
The floor

The same volume selection method is now applied to the volumes in the lower pane.

First press V, then select the first volume, hold CTRL/CTRL and select the second (or more) volume.

Now the floor can be drawn in.

Step 7:
The back wall

Once again we use volume selection to draw in the back wall. Mark the volume, draw in the back wall.

Step 8:
Provide the notch with plates

If you're having trouble dragging the panels into place, use the spacebar as you drag in to jump between volumes.

Step 9:
The construction floor below

As before, select volume, pull in horizontal plate.

Step 10:
Draw in the remaining elements

From here you can equip the cabinet with elements as usual, assign processing and materials and place fittings.

In order to place the door hinges, the doors must be shown again. To do this, use the J key.

Complete!

Der Beitrag Doppeltüren ohne Verlinken erschien zuerst auf Tibek CNC-Technik - Macher von SmartWOP.

Insertion of drawers

Ralf Raaf — Thu, 17 Aug 2023 10:53:08 +0000

Insertion of drawers

If you use trusses in your project, the position of the truss may prevent underlying components from being pushed to the position you want.

If your furniture drawers contains, you must proceed as follows to place them with SmartWOP.

When you have designed your furniture to such an extent that the next step is to place drawers, click on “elements”.

Since the fittings for drawers are linked to the drawer front in SmartWOP, this must be positioned first.

Drag the drawer front to the desired location.

To one slamming drawer front to get you have to uncheck all “edition" remove.

If you use a drawer system that no front required, you can use the option “Use separators” transform the front into an invisible separator.

The Front/fitting displacement allows you to move the drawer front (or separator) and associated fittings together.

Once the front has been placed you can click on the “Fittings” in the lower right image. Then, in the upper part, make sure you do this drawer icon selected (and deselected the favorites if necessary - as long as the fitting you want is not a favorite).

In order for you to be able to place the fitting, the drawer front must be visible. You can then, for example, hide the fronts by pressing the F key in order to have a better view of the interior of your furniture.

In this example, rails from the Häfele company were selected and dragged into the example. The light blue lines now specify the maximum dimensions of your drawer.

Now, for example, you can add one of your als component Pull in the saved drawers here, make the fine adjustments (if necessary, attach handles, etc.) and you're done complete!

Der Beitrag Einfügen von Schubkästen erschien zuerst auf Tibek CNC-Technik - Macher von SmartWOP.

Trusses and elements

Ralf Raaf — Thu, 17 Aug 2023 10:46:44 +0000

Trusses and elements

If you use trusses in your project, the position of the truss may prevent underlying components from being pushed to the position you want.

In this example, the vertical truss has been placed flush with the rest of the elements.

All the following elements that are used under the traverse now have a recess that corresponds to the thickness of the traverse.

Since this is not always desired, the use of a divider allows it to be placed below the traverse without a recess.

Position before place the truss a divider with the distance equal to the width of the truss.

Place your truss and select “Top Only” or “Bottom Only” to get a single truss.

All of the components below are now placed over the entire base of the body again.

Tip: This principle also works if an element is required in front of or behind a horizontal truss.

Der Beitrag Traversen und Elemente erschien zuerst auf Tibek CNC-Technik - Macher von SmartWOP.

Construct the body with a miter

Ralf Raaf — Thu, 17 Aug 2023 10:31:36 +0000

How to design a carcass with mitre joints?

In SmartWOP you can only have mitre joints on Frontal and Diagonal Panels. How to design a carcass using those panels?

Select a Diagonal Panel instead of a horizontal Panel, but arrange it horizontally. Click on that panel and tick Left Mitre and/or Right Mitre.

In the construction, the carcass edges are mitred. No further adjustment of the vertical plates is required.

The miter for the front panels is adjusted in the same way:
click on the frontal plate and set the tick miter left and miter right.

In the construction, the carcass edges are mitred.

Der Beitrag Korpus auf Gehrung konstruieren erschien zuerst auf Tibek CNC-Technik - Macher von SmartWOP.

Decorative panel over several separate volumes

Ralf Raaf — Thu, 17 Aug 2023 09:40:14 +0000

How can a decorative screen be arranged over several separate volumes?

Decorative panel over several separate volumes

Following situation:

A continuous worktop is to be constructed from one piece across the corner using several individually installed base units.

So our goal looks like this:

The starting point:

Select the top shelf of the right and left base cabinet together.

Drag a decorative panel onto the construction.

The decorative panel thus spans all volumes.

It is not necessary to also select the volumes in between.

Only the outer volumes have to be selected.

The notching of the panel in the front area will be carried out using additional processing in woodWOP.

Select the cover plate and click on the button Edit woodWOP or button F4.

The file is opened in your woodWOP software.

Program the required edits.

Save the component to get back to SmartWOP.

Click on the cover plate again and also on the symbol To update.

The additional processing is implemented immediately.

Perfect - you're done!

Der Beitrag Dekorblende über mehrere getrennte Volumen erschien zuerst auf Tibek CNC-Technik - Macher von SmartWOP.

Fold thicker back wall

Ralf Raaf — Wed, 16 Aug 2023 14:41:32 +0000

How can a thicker back wall be rabbeted?

Click on the back wall. Change the thickness and the return according to your requirements.

In the next step, enter under the sub-item back panel rabbet the depth of the fold.

The property In front indicates the depth of the rebate all around on the inside.

A notice: The rabbet can be displayed as shown in the image with the Show material removal button activated.

The property Rear indicates the depth of the rebate all around on the outside.

The combination of both processing sides results in a rebate on both sides of the rear wall.

Air allowance rebate width there the required air to the surrounding rabbet.

If the rabbet processing is to be carried out on the CNC machine, please tick the box Machining on CNC.

Submit tool number the number of the tool that is used for the fold processing in your machine.

Der Beitrag Dickere Rückwand fälzen erschien zuerst auf Tibek CNC-Technik - Macher von SmartWOP.

Linking doors

Ralf Raaf — Wed, 16 Aug 2023 14:09:36 +0000

This function will help you if you want to place a door across several volumes in your furniture To link.

First drag doors over the desired volumes.

Select the two doors while holding CTRLbutton off.

Click on To link in the top menu bar under the tab Extras.

The doors have merged into one larger door.

Alternative:

The function volume (Key V) can be found in your menu bar in the tab “Home”

Both partial volumes are pressed CTRL button selected.

Now drag a door over the selected volumes.

Complete!

This process can also be used for other elements, such as shelves or construction shelves.

Linking doors

Der Beitrag Verlinkung von Türen erschien zuerst auf Tibek CNC-Technik - Macher von SmartWOP.